Pool Cover Straps Instructions

A pool safety cover is secured into the deck via straps springs and anchors. Lay cover over pool and adjust for equal overlap at all 4 corners of the pool.

Inground Swimming Pool Cover Installation

2 Mark Strap place locations on drill lines.

Pool cover straps instructions. Be sure there is an equal overlap on both sides and ends. Detailed installation instructions are available. Thanks for reading this post on how when and why to adjust your safety pool cover straps.

9 99-55-4395015 Strap Kit 1 INSTALLATION INSTRUCTIONS 1. Strap end Choose the appropriate instructions below for your pool setup. Refer to Anchor Plan provided with cover.

Strap Plate Strap Plate Snap a Barrel onto each Base and. Anchor drilling instructions on page 9 Then install both ends of a center strap CD across the pool width. GENERAL INSTRUCTIONS Step 1.

10 x Locate one of the straps near the center of the pool cover and If you dont have a concrete patio follow the manufacturers installation instructions for a. Set the Buckets over the Covers edges to hold it in place. Adjustable attachment straps k it used for attaching a pool cover solar blanket to a reel.

Using stakes and a rope lay a rope grid across the pool as shown in figure 1. 2 Metal Self-Drilling Screw Strap Plate Strap end Fig. A 20 x 40 rectangular pool takes a 22 x 42 cover.

Of a Save-T 3 automatic cover system or Autosave spa cover. Stretch the cover over the pool and use buckets of water to hold it in place. The brass anchors thread up to install the cover and thread down flush into the deck when the cover is removed.

If the cover has cutouts adjust for proper alignment now. Please use your solar blanket and reel assembly in the manner it was intended for. See our full video at httpsyoutubeVs2UDSEln3QThis is Part 1.

How to attach buckles to your solar cover feed straps through the buckles and install the. These instructions will work for any plastic cover even if it isnt a solar cover. Cover is 3 longer and wider than pool your overlap will be 16 all the way around pool.

Any plastic sheet can keep leaves and other debris out of the pool. Overlap may vary 11 to 14. Stretch cover across pool keeping even overlap on all sides.

For the proper overlap look at the rst page of this booklet or subtract the pool size from the cover size and divide by two. Locate and mark anchor position for straps 1 2 3 and 4. Keep this manual in a safe location for future reference.

The WorldвЂs Finest Pool and Spa Products. Adjusting safety pool covers will not only give a better appearance but can improve the performance and lifespan of your pool cover and keep your pool clean during winter. 4 Cover bubbles down Attach Strap Plate to Tube see Fig.

Measure the cover and pool exactly. This nylon strapping kit was the easiest to attche by just snaping the plastic connectors at the edge of the pool cover and threading the strips through same as with the others for only 30 minutesPlease follow the instructions as. Place the remaining buckets evenly around the edges of the pool.

Adjust for correct overlap on all sides. First strap is placed 6 15 cm in from inside edge of pool or at the. Fill 5 Gallon Buckets with water and place one at each corner of the pool.

Please read directions before assembling. Pool Cover Installation Instructions. Solar covers will also degrade in acidic pH levels when pH falls below neutral 70.

Cover should not touch sides of the pool when rolling up. Please follow the instructions carefully so as to not void the war-ranty. To determine how far from pools edge to drill anchor add cover overlap plus 22.

2 X Trustworthy Source US. Straps x8 x 6 Fastener plates x8 Buckles x8 NOTE. Unroll the Cover and place it in position over the pool.

1 Strap Plate Attach Strap to Strap Plate see Fig. Easy-to-Essemble Webbing Strap Kit. Solar covers should never be used after shocking or super-chlorinating the poolLeave a solar cover safely stored in the shade whenever chlorine level is higher than 25 ppm.

Meyco Pool Covers Safety and Owners Manual and Installation Instructions Failure to follow instructions and safety precautions in this manual can result in serious injury or death. Leave an extra 4 10 cm on cover length if installing at mid-point or widest point to allow for fold see Fig. Pool Owner Order Pool Dealer Pool Size Cover Size Overlap Anchors Date Installed.

Of a Save-T 3 automatic cover system or Autosave spa cover. Installing your own safety pool cover is an easy. If you have determined a mid-pool placement or off-center it will be easier if you mark the cover then move it away from the pool and fold it bubbles in on a flat surface.

20 Strap Plates 10 - 26 Straps Hardware Kit. Fastener Assembly Instructions Tube Fig. This will save you time and make the attachment process much faster.

Adjust cover for equal overlap on all sides. Detailed installation instructions are available. This Sun2Solar universal attachment kit easily attaches your new solar cover to your existing in-ground or above ground reel system.

Your solar blanket is not a safety cover b. Cover must be laid out according to the plan to ensure proper installation. Anchor points should be located 18 from the edge of the cover not the edge of the pool and in line exactly with the strap.

10 Plastic Screws 4 Wing nuts bolts 25 Metal Self-Drilling Screws 1 Trim cover to clear inside top edge of pool. I hope this has been useful if so give us a Like or a Star Rating below. Congratulations on your purchase of our PRO SERIES Solar Reel for Inground Pools.

Very soft water with calcium hardness levels below 150 ppm.

Inground Swimming Pool Cover Installation Best Pool Covers